Secure LoRa Pager on ESP32: Text, Coordinates and Voice without Cellular Network

Написано

в

⏱️ ~4 min read

Secure LoRa Pager on ESP32: Text, Coordinates and Voice Without Cellular Connection

The modern world of communications presents many tasks that require autonomous data transmission over significant distances without using traditional networks. One such task is the creation of a secure LoRa pager based on the ESP32 microcontroller. In this article, we will explore all aspects of implementing such a device, including hardware selection, radio frequency settings, and software solutions to ensure reliable communication.

Task

The main task is to create an autonomous point-to-point communication system over several kilometers without using cellular networks, SIM cards, or the internet. Such a system can be useful for emergency services, agricultural enterprises, forestry, and other areas where stable internet connectivity is not possible or impractical.

Main requirements for the system:

  • Transmission of text messages.
  • Exchange of GPS coordinates.
  • Transmission of voice messages.
  • Reliable communication over distances up to 10 km.

Hardware and Radio Section

To implement the LoRa pager, we use the ESP32 microcontroller in combination with SX1262 or SX1278 transceivers operating at frequencies of 433 MHz and 868 MHz respectively. These components provide long-range data transmission with low power consumption.

The ESP32 is a powerful microcontroller supporting Wi-Fi, Bluetooth, and numerous peripheral devices. It has built-in antennas and can operate at frequencies of 2.4 GHz, making it ideal for integration with LoRa transceivers.

Transceivers SX1262 and SX1278 support various modulation parameters such as Spreading Factor (SF) and Bandwidth (BW). These parameters allow balancing the transmission range and data speed:

  • Spreading Factor (SF): Determines the number of chips used to encode one symbol. A high SF increases the range but decreases the transmission speed.
  • Bandwidth (BW): The frequency band width, affecting data transmission speed and resistance to noise.

To balance between range and speed, the following settings can be used:

  • SF = 7-12 (high SF for greater range, low SF for higher speed).
  • BW = 125 kHz or 250 kHz (wider bands provide high data transmission speed).

Radio Frequency Issues and Their Solution in Firmware

The radio frequency spectrum is not ideal, and various problems can arise when transmitting data over LoRa. Let’s consider the main ones and ways to solve them.

Packet Loss

One of the most common problems is packet loss. To address this, a software acknowledgment protocol (ACK protocol) similar to two checkmarks in Telegram can be used.

void sendPacket(uint8_t *data, size_t length) {
    // Send packet
    LoRa.beginPacket();
    LoRa.write(data, length);
    LoRa.endPacket();

    // Wait for ACK
    if (waitForAck()) {
        Serial.println("ACK received");
    } else {
        Serial.println("ACK timeout, retrying...");
        sendPacket(data, length); // Retry sending
    }
}

bool waitForAck() {
    unsigned long startTime = millis();
    while (millis() - startTime < ACK_TIMEOUT) {
        if (LoRa.parsePacket()) {
            return true;
        }
    }
    return false;
}

Collisions During Simultaneous Transmission

When multiple devices attempt to send data simultaneously, collisions can occur. To prevent this, random delays (random backoff) before responding can be used.

void sendResponse() {
    delay(random(100, 500)); // Random delay
    LoRa.beginPacket();
    LoRa.write(responseData, responseLength);
    LoRa.endPacket();
}

Voice Transmission Over a Narrow Channel

Transmitting voice messages over a narrow channel requires data compression. For this, the Codec2 codec can be used, which provides high sound quality at low bit rates.

void transmitVoice(uint8_t *voiceData, size_t length) {
    // Compress voice data
    uint8_t compressedData[length / 4]; // Example compression by a factor of 4
    codec2_encode(voiceData, compressedData);

    // Send compressed data
    LoRa.beginPacket();
    LoRa.write(compressedData, sizeof(compressedData));
    LoRa.endPacket();
}

Example Packet Structure

The packet structure includes a header (Header), payload (Payload), checksum (CRC), and delivery confirmation (ACK). Example packet structure:

struct Packet {
    uint8_t header[2]; // Header
    uint8_t payload[100]; // Payload
    uint16_t crc; // CRC Checksum
    bool ack; // Delivery Confirmation
};

Conclusions:

Creating a secure LoRa pager based on ESP32 requires careful selection of hardware and radio frequency settings, as well as developing software solutions to ensure reliable communication. Using the ACK protocol, random delays, and data compression effectively solves problems related to packet loss, collisions, and voice message transmission.

Such a system can find wide application in various fields where autonomous communication over significant distances without using traditional networks is required.

In subsequent articles, we will explore specific examples of implementation and testing of this system in more detail.

More from the Lab
← EcoFlow API and Reverse Engineering Inverters: Telemetry, Protobuf and Logic AnalyzerESP32 + Quansheng UV-K5: Wireless Wi-Fi Programmer and Reception Debugging →

Комментарии

Добавить комментарий

Ваш адрес email не будет опубликован. Обязательные поля помечены *